Armor Shield IX - DIY Consumer Review - S999SWS

Armor Shield IX - DIY Consumer Review - S999SWS

Reading Armor Shield IX - DIY Consumer Review - S999SWS 7 minutes Next Get Your Shine On: A Close Look at Cosmichrome Spray-on Chrome Coatings

It’s always reassuring when you can get information directly from the horse’s mouth. In the case of ceramic coating installations, with a superior product like Armor Shield IX, sometimes getting direct, non-solicited 3rd party reviews from an actual user helps to reinforce credibility.

Such is the case with this recently posted review on the forum at CaymanOC.com. User S999SWS posted this short recap of his prep-work and installation of Armor Shield IX on his 2016 Cayman. Posted below is his actual post, with pictures included.

Customer Review on Armor Shield IX Install on 2016 Porsche Cayman

I’ve thought about having a ceramic coating on my 2016 white Cayman for some time now but have been put off by the likely cost – around £1,000. I researched lots of products online and watched loads of YouTube videos, and eventually plumped for one in particular.

Hopefully, what follows below will save some of you from having to sift through the plethora of detailing products for your cherished Porsche. I had a couple of scrapes on my valences – curse those high curbs! — and Chips Away in Plymouth sorted them out on my driveway, which couldn’t have been more convenient.

Their operator, Lee, did a fantastic job. I had to wait about six weeks for the repair to fully harden before I could do any coating work, but I didn’t want to rush it and jeopardize his craftsmanship. The first thing you must do to prepare the car is to strip off any old wax and dirt. I have the Autobrite snow foam lance and only use their own snow foam product.

It really works well and after hosing down the car with water, the snow foam goes on and then you wait 20 minutes for it to work its magic.

Rinse off and get two buckets ready for the wash. I used Chemical Guys’ Clean Slate wash. There are plenty of others but this one was fine. I then used a clay bar, and finished with a Meguiar’s oscillating machine, using Poorboy’s wax-free polish. You must not use a polish which contains additives – especially wax. You have been warned! When you’re ready to apply the liquid coating, you must wipe down each panel, or part of a panel depending on how big the area is, with an IPA panel wipe alcohol spray. I used Mr. Bling’s panel wipe.

I split the roof into halves and the bonnet into three sections, then the doors, wings, etc., and used a print of a generic car plan so I didn’t forget how far I’d got.

The IPA wipe is used prior to each panel’s treatment and take care when using this or you may end up seeing pink elephants! After some research, I decided to use AvalonKing’s Armor Shield IX nano-ceramic coating.

Their website contains a wealth of easy-to-follow instructions and videos, also their very fast response to emails is a reassuring bonus.

When it’s time to use the coating, have everything to hand and as the small bottle is easily overturned, designate a safe spot to put it down. Shake the bottle, and with the supplied small cloth wrapped around the sponge applicator, apply six or seven drops and wipe gently up and down and then across the entire small area you’re treating to ensure it’s all covered. The cloth is a bit small and does get slippery, so it requires a little care not to drop it. But they give you three, so you can always use another.

You’ll know when the pad needs refreshing as it loses its slipperiness and starts to grab, so just put a few more drops on. Just make sure all the area has a very thin coating on.

Now you must wait for it to start to dry. The instructions suggest sometimes depending on temperature, but working in a dry garage, I found it took about five or six minutes before it was ready to buff out. It’s tempting to spend that time just admiring the Cayman’s pristine bodywork, but I used the drying time to apply IPA on the next panel I’d be working on.

When buffing, use REALLY LIGHT pressure. Just gently skim the supplied microfiber cloth over the surface – don’t try to polish it, just a light buffing can pick up any high spots or remaining wetness – and this will get the paintwork gleaming. After buffing, mark up your car diagram and move on to the next panel.

After finishing, I let it rest for a couple of hours, then reapplied the coating again to the entire car, to give it the recommended two coats. You don’t need to use the IPA again. I found that one bottle of the ceramic coating was enough to treat my Cayman twice, and though I didn’t treat my wheels, there was some leftover so perhaps I could have done them too.

Getting this treatment right is not a quick job, but it’s worth taking the time to be methodical over it. Here’s how long each step took me, excluding the repair job

  • Foam 45 mins
  • Dewax 45 mins
  • Clay 1 hr.
  • Polish 3 hrs.
  • CC (1) 1 hr. 15 mins
  • Wait 2 hours
  • CC (2) 1 hr.

So about 10 hours in total, and the cost, excluding my snow foam lance, machine polisher, and pressure washer, was about £100. A fantastic saving from an anticipated £1,000, and after leaving the car in the garage for a week to make sure it didn’t get wet, I found the finish hardened into a glass-like covering. It feels so smooth and solid that I am delighted with the result. AvalonKing says it should work for at least two years, but if the car is garaged, I reckon it should last a lot longer.

Now when the car needs a clean, and after just using the snow foam, (unless the car is dirty after a long-wet drive), I usually don’t have to wash it with the shampoo as the snow foam appears to remove all the dirt. The shampoo I use now is Poorboy’s Super Slick Suds, which doesn’t contain additives or waxes. After a drive, any bugs can be removed very easily with a detailing spray and microfiber cloth.

So, there you have it. It’s very satisfying to see the results – any rain or water just runs off the car. I think it was a job well done.

I’d be delighted to see any feedback you have about this review, and I hope it will be of some use to you.

SWS

2 comments

Dale Pearl

Dale Pearl

Hi Michael!
We don’t want to give other companies free advertisement but drop us an email at hello@test3.unicorns.rocks and we’ll give you some recommendations!

Hi Michael!
We don’t want to give other companies free advertisement but drop us an email at hello@test3.unicorns.rocks and we’ll give you some recommendations!

Michael Reynosa

Michael Reynosa

Can you recommend a detailing spray and should I use use a hybrid ceramic detailing spray ?

Can you recommend a detailing spray and should I use use a hybrid ceramic detailing spray ?

Leave a comment

All comments are moderated before being published.

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Subscribe to our newsletter

Promotions, new products and sales. Directly to your inbox.